How to Install Showcase Track Lighting: Step-by-Step Guide

A complete walkthrough for installing the LightrixTech magnetic track system in display cases – covering the round track (surface and concealed bases), the flat track on wood, glass and metal, the flexible track, and the transparent rail. Every method below comes from the official installation manual that ships with the product.

Safety first: the entire system runs on 12V DC low voltage – never connect a rail directly to mains. Always cut off the external power supply before installation. Do not disassemble a base after it is glued down: the internal wires may break.

Method 1 – Round track (T-01)

A. Surface-mounted base

  1. Drill a small hole for the wires to pass through the deck.
  2. Loosen the cover of the surface-mounted base.
  3. Secure the base with the supplied bolts.
  4. Tighten the cover back on – the rail is now fixed and powered.

B. Concealed base (hidden wiring)

  1. Drill a hole about 18 mm in diameter for the concealed base.
  2. Insert the base into the hole and fasten it with the provided screw bolt.
  3. Use a small wrench to loosen the fixing screws and adjust the track height.

Method 2 – Flat track (T-02): three ways to mount

SurfaceMethod
Wooden boardFix the flat track pole with the equipped screws
Glass boardGlue the track onto the glass using UV glue
Iron boardPaste the matching magnetic strip on the back of the track, then install by magnetic suction

Method 3 – Flexible track (T-03)

The flexible track bends to follow curved counters and circular towers. It mounts with the same three methods as the flat track – screws on wood, UV glue on glass, or the magnetic strip on iron.

Method 4 – Transparent rail (TR-1)

  1. Check the front and back sides: the smooth side is not conductive – put the non-smooth side up.
  2. Place the base where the spotlight needs to be installed.
  3. Attach the base to glass or a smooth surface with the adhesive pad.
  4. Power up with the power connector.
  5. Install the magnetic spotlights onto the rail.

Top-down vs side lighting: pick the layout before you drill

Top installation (flat track on the cabinet top)Side installation (two round tracks, top to bottom)
Visual resultTracks and spotlights stay hidden from viewTracks and spotlights are exposed to sight (14 mm rail diameter)
Lighting effectLight comes from above – good, but not as dimensional as side lightSide light gives a better display effect on the exhibits
FlexibilityPositions fixed to the top rail; replacement is less convenientPosition and direction adjustable freely along both rails
Head choiceLight source sits over a metre away – higher-power heads neededShort source-to-exhibit distance – more models to choose from

After installation

  • Slide each head along the rail and aim it – the magnetic block holds anywhere on the rail.
  • Verify every head lights up before closing the case; a dark spot usually means a connector seat is not fully engaged.
  • If you plan to dim, confirm the driver is dimmable and matched to your control system in the driver selection guide.

Questions installers ask

What voltage do the rails use?

12V DC across the whole system. The transformer converts mains to 12V DC; never wire a rail to mains directly. For long runs, 24V versions are available on request.

Can I mount the track without drilling the glass?

Yes – UV glue on glass (flat track) or the adhesive pad of the transparent rail both attach without drilling. Screws are only needed on wooden boards.

Which track is best for a curved counter?

The flexible track (T-03). It bends to the counter radius and mounts with screws, UV glue or the magnetic strip, same as the flat track.

How many spotlights can one power feed drive?

Keep one power feed to roughly 20 heads or fewer, and size the transformer at total wattage Ă— 1.25. The showcase lighting calculator below does this maths for your cabinet automatically.

Plan and verify before you order

Send Us a Message

Customize your own lamp

Get A Free Consultation And Estimate