Magnetic Track & Accessories Guide for Showcase Lighting
A display case lighting project is only as good as its rails, connectors and power supplies. This guide maps every track and accessory in the LightrixTech system to the right mounting surface and cabinet type, so your installer orders the complete kit the first time – no mid-project delays waiting for a missing end cap or connector.
The four track types at a glance
| Track | Profile | Mounting methods | Best for |
|---|---|---|---|
| T-02 Flat track (aluminium) | Low-profile flat rail | 1. Screws on wooden boards 2. UV glue on glass 3. Magnetic strip on iron boards | The default choice for most cabinets – works on wood, glass and metal surfaces alike |
| T-01 Round track (Ø14 mm) | Cylindrical rail | Surface-mounted base, or concealed base in a pre-drilled Ø18 mm hole | Cabinets where wiring should disappear into the deck; also top-to-bottom vertical runs |
| T-03 Flexible track | Bendable flat rail | Same three methods as flat track | Curved counters, circular towers and non-standard shapes |
| TR-1 Transparent rail | Clear acrylic rail | Adhesive pad on glass or smooth surfaces (non-conductive side up) | All-glass vitrines where an invisible power rail matters most |
All rails are low-voltage DC 12V systems: the spotlight heads attach via a conductive magnetic block and can be repositioned anywhere along the rail.
Match the track to your mounting surface
| Surface | Recommended method | Notes |
|---|---|---|
| Wooden deck / MDF | Screws (supplied bolts) | Drill a small pass-through hole for the wires |
| Glass shelf or glass deck | UV glue (flat track) or TR-1 transparent rail | UV glue cures clear; no mechanical fixing needed |
| Iron / steel plate | Magnetic strip bonded to the rail back | Fastest install and fully repositionable |
| Cabinet top with hidden wiring | T-01 round track, concealed base | Requires a Ø18 mm drilled hole; height is adjustable after fitting |
Accessories that complete the kit
| Accessory | Role |
|---|---|
| Magnetic tape / strip | Bonds flat track to iron surfaces |
| Track connector (new / legacy type) | Joins rail sections in a straight run or an L-corner |
| Power connector / feed | Injects 12V DC from the transformer into the rail |
| End caps (flat / flexible / round) | Closes and finishes the rail ends |
| Surface & concealed bases | Fix round track to the deck (surface) or into a Ø18 mm hole (concealed) |
| 12V transformers (3W / 10W / 25W) | Converts mains to the low-voltage DC the system runs on |
Tell us the rail length, head count and mounting surface with your enquiry and we will return a complete bill of materials – rails, connectors, end caps, transformer – sized to your cabinet.
Transformer sizing in one formula
Add up the rated wattage of every head on the circuit, then multiply by 1.25 and pick the next transformer size up.
Example: 4 × CHIB7517-P-2W heads = 8 W → 8 × 1.25 = 10 W → one 12V / 10W transformer. For longer runs, step up to 24V to halve the current – see the driver selection guide below.
Questions buyers ask about tracks and accessories
Which track should I use for an all-glass display case?
Two options: the T-02 flat track bonded with UV glue (cures clear and holds securely), or the TR-1 transparent rail when you want the power rail itself to be almost invisible. Both attach without drilling the glass.
Can I reposition the spotlights after installation?
Yes. Every head attaches with a conductive magnetic block, so you can slide it anywhere along the rail and re-aim it at any time – useful when the display layout changes between seasons.
What transformer do I need for my cabinet?
Total the wattage of all heads, multiply by 1.25, and choose the next size up from the 12V range (3W, 10W or 25W). One power feed should drive roughly 20 heads or fewer. For a full worked example, use the showcase lighting calculator linked below.
Do all your spotlight models fit these tracks?
The CHIB75xx magnetic track heads and LF mini track heads all attach to the same rail system. Mini spotlight models (surface-base versions) mount on a drilled base instead of the rail – the configuration checklist below helps you confirm the match per model.
